- #Yamaha rocketbox replacement key pdf
- #Yamaha rocketbox replacement key zip
- #Yamaha rocketbox replacement key free
Screw the housing back on and re-rivet the points you drilled. When you reinsert the cartridge in to the housing make sure that the sliding bolt (that your key turns) is fully in the open position, otherwse your key won't do a thing. (the one I did had a snapped key so I'm assuming this part is easier if you are just changing locks for keyed alike purposes)įitting the new lock in to it's cartridge should be easy enough. You can separate the inner and outer latch mechanism with a T10 Torx wrench.
#Yamaha rocketbox replacement key pdf
This PDF should provide a few options to troubleshoot this issue and get the box operational. To get the barrel lock out of it's cartridge you'll have to push the tumblers in from the back with a very small screwdriver and gradually work it out. If your Rocketbox handle is allowing the key to turn part way, but not fully, it may be that 2 parts are colliding inside the box handle. Theres various wedges in the plastic which you should try to hold open then a flat screwdriver near the cog should lever the whole thing out. You'll have to take out the lock cartridge next. Unscrew these (I used a small ratchet with a pozi bit rather than a screwdriver) and remove the plastic unit. Inside the box pull the plastic unit away from you (bending the aluminium strip slightly but this is fine) gaining access to 2 screws. Pop off the 3 rubber caps around the lock and drill out the rivets. Just replaced the locks on an Atlantis 200 which should be the same.
#Yamaha rocketbox replacement key free
Fortunately my lid was open so I was able to free the sliders inside - wd40, gently tapping the end of the slider back and forth until it was free. One bit I picked out with a paper clip, the side I had to drill the whole barrel out. I'm my case both sides were seized solid - it was assumed that the locks themselves were seized solid these were forced until the keys snapped off. The locking bar slider is aluminium, about 4 feet long and a lot for the little key to move, especially when dirty, clogged with sand etc. Basically the issue is not the lock but the sliding locking bar inside the box, when you lock or unlock the lock you are just turning a small Lever inside the locking bar mechanism which slides the locking bar left or right to clamp or release the 3 hinge pins on the lid. If your roof box lock appears to be jammed, key stuck in, broken off etc here is my advice based on what happened to mine. I know this is old but there doesn't seem to be much on the web about this common problem. We use the latest up to date electronic technology for cutting keys to code. )Īs to the PVC, I think it was 1", and in fact it was not really big enough to completely cover the locking bars, so I didn't tighten the zip-ties down all the way, if I did it again I'd get bigger pipe or heat it and flatten it out a bit, but I just tested this setup on a 1200 mile trip and it worked great, noticeably smoother opening and closing. Description: Replacement keys cut for Yamaha motor cycles. The only remaining issue I have now is if I pile stuff too high and it puts upward pressure on the box lid, so don't do that.
#Yamaha rocketbox replacement key zip
Also consider what I did which helps 99% of the rest of the way: buy a couple feet of PVC, large enough to cover the sliding locking bars, cut it in half the long way, attach it to the box over the locking bars (I drilled holes and used zip ties). The main reason I'm posting, once it's free to open, lubricate behind the sliding locking bars with Silicon Spray, this helps A LOT.ģ. Don't use WD40, it attracts dust and grime later, use Silicon Spray or graphite dustĢ. My CLP110 Clavinova is playable again.I did a lot of research on forums about this and wanted to consolidate the results:ġ. Keys arrived in about three days, worked perfectly. My customers and my family thanks you too. Parts were hard to find during the pandemic but Keyboard Kountry saved the day together we got the job done. Ignition Switch Lock&Fuel Gas Cap Key Set For Suzuki SV650 GSX1400 DL650 1000 RE. Cylinder Piston Gasket 83mmm For Yamaha Kodiak 400 93-99 Big Bear 400 00-12 RE. Posted by Austin Keyboards on Jul 16th 2020īeing an independent technician it was great to find the replacement keys for a repair on a Yamaha Motif 8. For Yamaha FZ6 FZ6-SA2 (Naked, ABS) 2007-2009. I' m glad to order key replacements every time I need to fix a Yamaha. Had to replace a key on a S90XS and the key fits perfectly fine, there is no even a 'whitening' difference. 88 Key Piano Keyboard Dust Cover for Electronic Keyboard Digital Piano Protector. This one was all I needed to give me a great piano for the house. NEW OEM Replacement Piano Key For Yamaha CLP CVP, P, Motif, GH3 GHD GHS. I managed to straighten it enough so that the keys were not sticking, glued a couple of them buthad to replace one black key. I picked up a used Yamaha CP300 for $100 but it had some sticking keys, mainly due to the front rail being dentedd in a couple of places. Posted by Alistair Dunsmore on Mar 28th 2021
0 kommentar(er)
